人人澡超碰碰 I 久草在线视频新时代视频 I 狠狠躁夜夜躁人人躁婷婷 I 哪里可以看免费毛片 I 麻豆果冻传媒2021精品传媒一区下载 I 久久综合九色综合欧美狠 I 婷婷中文字幕 I 不卡免费av I 久久只精品 I 一级做a爰片性色毛片99 I 在线观看黄色av网站 I 最新地址在线播放 I 国产v片在线播放 I jlzzz中国jizz老师水多 I 中文字幕一区一区三区 I 肉体暴力强伦轩在线播放 I 久色综 I 欧美日韩国产亚洲一区 I 国内黄色大片 I 色噜噜噜亚洲男人的天堂 I 欧美freesex黑人又粗又大 I 欧美日韩大片在线观看 I 精品二区国产 I 911国产视频 I 中国老头性hd I 又黄又免费视频 I 国产情侣自拍一区 I 成人免费91 I 色av久 I 色哟哟国产精品 I 一级免费看 I 村长侵犯糟蹋h双性 I 日韩毛片免费视频 I 日本玖玖视频 I 男人都懂的网站 I 韩国甜性涩爱 I 亚洲欧美综合视频 I 久久久久欧美精品网站 I 男女无遮挡免费视频 I av女优动态图 I 欧韩一级片 I 草草地址线路①屁屁影院成人 I 午夜精品久久久久久仙踪林 I 翔田千里在线观看 I 国产在线国偷精品产拍免费观看 I 人妻色综合网站 I 少妇直播视频在线观看 I 亚洲s码欧洲m码在线观看 I 久久久久免费精品国产 I 午夜黄色 I 青青操成人 I 舌吻一边亲一边摸 I 免费黄网站在线看 I 国产一区二区麻豆视频 I 操她上瘾小说 I 久久久久夜夜夜精品国产 I 成年人免费视频播放

The reason for the insufficient suction of stone sucker, I will introduce to you. Because the heat capacity of semiconductor rectifier element is very small, when the rectifier is overloaded, the temperature of the element rises sharply and the diode is burned. Rectifier components will be aging, there will be a degenerative phenomenon, resulting in the output of the electric bed, so that the suction of the vacuum sucker is insufficient. The inductance of the force line device by dry vacuum suction cup is very large, which will produce a large overvoltage at the moment of disconnecting the coil and may break down the rectifier element. The gas consumption of the straight air generator is determined by the diameter of the working nozzle, but it is also related to the working pressure. With the same nozzle diameter, the air consumption increases with the increase of working pressure. The diameter of nozzle is the main basis for selecting vacuum generator. The larger the nozzle diameter, the larger the suction flow and gas consumption, and the lower the vacuum degree: the smaller the nozzle diameter, the smaller the suction flow and gas consumption, but the higher the vacuum degree. To change the tube base, first unscrew the 2 screws (with gaskets) on the side of the manifold base, replace the old manifold base with a new one, and then put the gasket on the screw, pay attention to the screw with equal force.

In vacuum sensor, turn off the vacuum sensor on the side of 2 screws, and remove the vacuum sensor, then twist off vacuum sensor below the four screws (with washer), and then changed into a new vacuum sensor and put on the washer screw on the base of screw, will be in a good vacuum sensor installation back in vacuum, on the last point on the surface of the upper screw again: in silencer, First screw off the straight empty generator surface, remove the muffler, there is a relay pipe connection in the middle, and then remove the muffler below the 2 black nails, replace the old muffler with the new, screw the muffler base screw, install the relay pipe in the middle, and then reinstall the muffler, and then screw on the side screw.